Aerial Imaging Services in Clovis, NM
High plains landscape with Cannon AFB flight line and agricultural fields stretching to the horizon
Clovis (New Mexico) is part of the Clovis Micropolitan Area and has a population of approximately 38,567. Clovis economy centers on Cannon Air Force Base MQ-9 Reaper operations and agriculture. Military construction and agricultural processing drive aerial imaging demand, with the restricted military airspace creating operational planning challenges.
Serving Curry County & the Clovis Micropolitan Area area
Request a Free Quote
Get a Clovis Aerial Quote
Drone Services Serving Clovis, NM
Clovis economy centers on Cannon Air Force Base MQ-9 Reaper operations and agriculture. Military construction and agricultural processing drive aerial imaging demand, with the restricted military airspace creating operational planning challenges.
Drone Regulations & Airspace Rules for Clovis
FAA Part 107 Requirements
Flying for hire in Clovis? That is commercial operation under FAA Part 107, which requires a Remote Pilot Certificate — a credential we verify for every operator.
State Drone Laws
Commercial drone work in Clovis follows New Mexico UAS law (SB 240 (2021), NMSA Ch. 60 Art. 6A), with city-level rules on top: Clovis follows FAA Part 107 regulations. Full New Mexico drone law →
Local Ordinances
Clovis follows FAA Part 107 regulations. The city does not have additional municipal drone ordinances. Cannon Air Force Base, home to the 27th Special Operations Wing with MQ-9 Reaper drone operations, has extensive restricted airspace immediately west of the city. Operators must coordinate with Cannon AFB for any flights near the restricted boundary.
Restricted Airspace
- Class D airspace around Clovis Regional Airport (CVN)
- Cannon AFB restricted airspace (R-5102, R-5103) directly west of city
- MQ-9 Reaper drone operations at Cannon AFB create frequent TFRs
- Vast surrounding agricultural and ranch land with minimal restrictions beyond military zones
Airports in the area: Clovis Regional Airport (CVN), Cannon Air Force Base (CVS)
Aerial Imaging Pricing Across New Mexico
Cost ranges are based on market data for Clovis Micropolitan Area. Actual pricing depends on site size, complexity, and deliverables.
| Service Type | Low End | High End |
|---|---|---|
| Topographic Data Collection | $1,150 | $5,750 |
| Drone Inspection | $475 | $2,600 |
| LiDAR Scanning | $1,875 | $9,400 |
| Environmental Monitoring | $950 | $4,750 |
| Aerial Imagery | $275 | $1,600 |
| Construction Monitoring | $575 | $2,900 |
| Real Estate Photography | $200 | $1,050 |
| Roof Inspection | $200 | $1,250 |
Free cost calculator, ROI calculator, and 14-page buyer's guide. No signup required.
Are you a drone operator serving Clovis? List your business on AeriusView and get pre-qualified leads in your service area.
List Your Business →How Clovis Builders Use Aerial Data
Clovis construction is driven by military infrastructure at Cannon Air Force Base, agricultural processing, and residential development. Major projects include base facility upgrades, the Curry County courthouse area development, and residential subdivision growth. Cannon AFB expansion for the 27th Special Operations Wing creates specialized defense construction demand.
Active Developers in the Area:
- Department of Defense — Cannon AFB facility upgrades and special operations infrastructure
- City of Clovis — Municipal facility upgrades and residential infrastructure
- Agricultural processing companies — Peanut and dairy processing facility construction
Why Hire Through Aerius View in Clovis, NM?
FAA-Certified
Every operator holds an active Part 107 Remote Pilot Certificate.
Local to Clovis
Based in the Clovis Micropolitan Area and fluent in New Mexico drone law, with 3 nearby Clovis service communities in reach.
No Cost to Quote
Submit your project at no charge. Pay the operator directly if you proceed.
Fast Turnaround
Quotes in Clovis commonly move inside 2 business days once your request is in.
AeriusView is expanding in Clovis, NM
Clovis is an expansion market for the network, with demand driven by projects from Department of Defense and other local builders. Submit here and a verified operator covering Curry County is assigned.
Request a QuoteDrone Data Deliverables for Clovis Projects
These are the files you receive with a Clovis booking — all compatible with standard construction and engineering software. Projects like those delivered for Department of Defense across Curry County need data that drops straight into their workflow.
- Point clouds (LAS/LAZ) for 3D modeling and volumetric analysis
- DEM/DSM terrain models for cut/fill and grade analysis
- Contour lines (DXF/DWG, CAD-ready) for Civil 3D and Revit
- Progress reports with side-by-side comparisons for construction monitoring
- Orthomosaic maps (GeoTIFF) for site overview and documentation
- Coordinate systems matched to your project datum — the New Mexico State Plane zone, UTM, or a local datum your surveyor specifies
Insurance & Liability Protection
Pilot Insurance Required
Every operator matched to a Clovis project carries active liability insurance — minimum $1,000,000 general liability, verified from the certificate before the pilot joins the network. Clovis follows FAA Part 107 regulations. The city does not have additional municipal drone ordinances. Cannon Air Force Base, home to the 27th Special Operations Wing with MQ-9 Reaper drone operations, has extensive restricted airspace immediately west of the city. Operators must coordinate with Cannon AFB for any flights near the restricted boundary.
FAA Part 107 Verified
Each pilot's Remote Pilot Certificate is checked against the FAA Airmen Inquiry before they can serve Curry County bookings. Expired certificates are flagged automatically.
Equipment Documentation
Pilots register their airframes and sensors (RGB, LiDAR, thermal, multispectral) so Clovis requests route to crews with the right payload for the job.
Site Safety Coordination
Pilots coordinate with your site superintendent for safe operations on active Clovis construction sites, including flight plans that avoid worker areas and equipment zones. Clovis follows FAA Part 107 regulations. The city does not have additional municipal drone ordinances. Cannon Air Force Base, home to the 27th Special Operations Wing with MQ-9 Reaper drone operations, has extensive restricted airspace immediately west of the city. Operators must coordinate with Cannon AFB for any flights near the restricted boundary.
Drone Services FAQ for Clovis, NM
Can I fly a drone near Cannon Air Force Base in Clovis?
Cannon AFB has extensive restricted airspace (R-5102, R-5103) immediately west of Clovis. The base conducts MQ-9 Reaper drone operations, making the restricted zone frequently active. Drone operators must check NOTAMs and coordinate with Cannon AFB air traffic control for any flights near the restricted boundary.
What is the aerial imaging market like in Clovis?
Clovis has a niche aerial imaging market driven by military base infrastructure, agricultural operations, and residential development. Cannon AFB construction creates demand for construction monitoring and as-built documentation. Agricultural data collection needs include crop health monitoring and irrigation planning.
Does Clovis have controlled airspace?
Clovis Regional Airport (CVN) has Class D airspace. Cannon Air Force Base (CVS) has restricted military airspace. Both require LAANC authorization or military coordination for drone operations in their respective controlled zones.
What construction projects are happening at Cannon AFB?
Cannon AFB has ongoing construction for the 27th Special Operations Wing, including facility upgrades, training infrastructure, and housing. Defense construction projects require specialized security coordination and may have additional drone flight restrictions beyond the standard restricted airspace.
Are there agricultural aerial imaging opportunities near Clovis?
The Curry County area has significant peanut farming, dairy operations, and cattle ranching. Multispectral imaging for crop health, aerial mapping for irrigation planning, and environmental monitoring for dairy operations are all potential service areas.
How does Clovis weather affect drone flying?
Clovis is on the high plains at approximately 4,300 feet elevation. Spring wind events can be severe with sustained winds over 30 mph. Summer brings thunderstorms and dust storms. Morning flights in calm conditions are most reliable. The flat terrain offers few natural wind breaks.
Aerial Imaging Terms for Clovis Projects
First aerial project in Clovis? These terms cover the deliverables local pilots will quote you. Most Clovis projects in our cost table start around $200.
Orthomosaic
A geometrically corrected aerial photo map stitched from many images.
Point Cloud
A 3D dataset of points representing the captured surface.
Real-Time Kinematic
RTK GPS correction for centimeter-level positional accuracy.
LiDAR
Laser scanning that captures terrain through vegetation.
Digital Elevation Model
A 3D representation of terrain elevation across the site.
Ground Control Point
Known reference markers used to anchor and validate mapping accuracy.
Aerial Mapping
Data collection from above to map and measure a site.
Volumetrics
Cut/fill and stockpile volume calculations derived from terrain models.
Nearby Cities
Are You a Drone Operator in Clovis?
Curry County buyers search here — 3 active developers tracked in Clovis alone. Join the network and get matched leads. First lead free.
Ready to Start Your Project in Clovis, NM?
Tell us about your Clovis project and we route it to a vetted local pilot — free, no obligation. Projects in Curry County start around $200.
Request a Free QuoteAeriusView connects clients with FAA-certified drone operators. Services are not licensed land surveying. Deliverables are not authoritative for boundary determination, design, or legal purposes.